I'm just getting in to learning Polycom and have completed RPIIT202 & would like a freindly pointer in order to set up my lab with outbound sip calls.
In the RPIIT202 course we learned how to do basic deployment & configuration of RPRM, DMA Core/Edge and RPCS.
One thing which is not covered in the course though is the dial plan and being completely new to the Polycom terminology I am at a loss :(
I have now deployed an identical lab as we did in the RPIIT202 course (using the lab guide) in my home lab but I am a bit lost on the workflow needed to enable sip calls out to the internet (example: email@example.com or firstname.lastname@example.org) and also the correct setup I should use for these type of calls to be routed firstly to the DMA Edge and then out to the internet via the DMA Edge external interface which resides in my DMZ.
Setup is as follows:
DMA CORE (v10.0.0_P3)--> FW <--> DMA EDGE <-->FW <--> INTERNET
So far I have created an external sip peer on DMA Core which points to DMA Edge and a dial rule called "B2B Calls" in default dial plan which resolve to the DMA Edge Sip Peer.
I have also changed ACL on Edge to allow all (just for testing).
Here is a test of the dial plan making a sip call from a registered endpoint to blujeans networks:
#1: Dial registered endpoints by alias: SignalingAlias [aliasType=SIP_URI, alias=sip:email@example.com] is not registered.SignalingAlias [aliasType=SIP_URI, alias=sip:firstname.lastname@example.org] is not registered.SignalingAlias [aliasType=H323_H323ID, alias=meet] is not registered.SignalingAlias [aliasType=H323_EMAILID, email@example.com] is not registered. #2: Dial by conference room: The conference room [meet] does not exist. #3: Dial to SIP conference factory: Rule disabled. #4: Dial by virtual entry queue ID: No entry queue is found. #5: Dial to on-premises RealConnect\u2122 conference: Rule disabled. #6: Dial services by prefix: No prefix device is found. #7: Dial external networks by H.323 URL, Email ID or SIP URI: Domain is controlled by DMA: bjn.vc #8: Dial endpoints by IP address: The user part [sip:firstname.lastname@example.org] has no IP address in it. #9: Dial to RealConnect conference by external Skype system conference ID: Rule disabled. #10: B2B Calls: The call was accepted by this dial rule. Transformed dial string is [sip:email@example.com]. The call was accepted by dial rule #10
The problem is when I call the "sip:firstname.lastname@example.org" from RPD registered to the DMA Core I get call rejected from DMA Edge :
DMA CORE +++++++++++++ Start time: 2019-05-27 04:28:41.764 PM End time: 2019-05-27 04:28:41.818 PM Duration: 00:00:00 Signaling: SIP Incoming call interface (IP): 10.10.10.102 Signaling port: 5060 ACL: Factory Core ACL Server(s): dma.lear.local:5060 Dial plan: Default Dial Plan Dial rule: 10. B2B Calls Dial string: sip:email@example.com Final dial string: sip:firstname.lastname@example.org Call ID: 721de973-bfe0-4992-8876-70831ef30b61 DMA EDGE +++++++++++++ Start time: 2019-05-27 04:28:41.808 PM End time: 2019-05-27 04:28:41.811 PM Duration: 00:00:00 Signaling: SIP Incoming call interface (IP): Signaling port: Server(s): dma-e.lear.local:5060 Dial plan: Dial rule: Dial string: sip:email@example.com Final dial string: sip:firstname.lastname@example.org Call ID: 721de973-bfe0-4992-8876-70831ef30b61
On DMA EdgeI can see that it seems not able to resolve the sip uri to an address (see attached jpg)
If anybody has a sample configuration of setting up basic outbound calls to internet I would be very gratefull :)
We don't typically use an External SIP peer for this type of use case. If you look at the RPRM site topology and choose one of your sites, go to H323 and SIP tabs. Here you can add an SBC IP address which is the internal interface for your DMA Edge server. When the DMA Core processes the dial string, it will route the call based what is listed in the site. You must do this for all sites.
Another common element missed all the time is not telling the DMA what domains it is the owner. If not domains are listed, then all domains are local. If this configuration is not updated, the DMA Core will not forward the call to the DMA Edge. Go to Call Server, domains or domain restrictions depending the version and enter the domain for the DMA.
Then once the above is done. You should see the DMA Core send the call using "dial by external networks" dial rule (#7).
#7: Dial external networks by H.323 URL, Email ID or SIP URI: Domain is controlled by DMA: bjn.vc
Give this a shot and let us know what happens?