Plantronics + Polycom. Now together as Poly Logo

Lync Event Log Error 14435 - LS Protocol Stack

SOLVED
Polycom Employee & Community Manager

Re: Lync Event Log Error 14435 - LS Protocol Stack

Hello all,

we found that this was an issue on the Polycom end and have corercted this in the following software:

 

  • Trio UC Software 5.5.3 or later

  • VVX UC Software 5.5.4, 5.7.0 and in a future 5.6.2


Please ensure to provide some feedback if this reply has helped you so other users can profit from your experience.

Best Regards

Steffen Baier

Polycom Global Services




<======== Signature / Disclaimer ========>
Please be aware:For questions about the type of support to expect please check here

Please also ensure you always check the VoIP , Video Endpoint , Skype for Business , PSTN or RPM FAQ's

Please remember, if you see a post that helped you , and it answers your question, please mark it as an "Accept as Solution".

The title Polycom Employee & Community Manager is an automatic setting within the community and any forum reply or post is based upon my personal experience and does not reflect the opinion or view of my employer.
Poly employee participation within this community is not mandatory and any post or FAQ article provided by myself is done either during my working hours or outside working hours, in my private time, and maybe answered on weekends, bank holidays or personal holidays.
Message 11 of 14
Highlighted
Occasional Advisor

Re: Lync Event Log Error 14435 - LS Protocol Stack

Worked for me.

 

Regards,

Tobias

Message 12 of 14
Occasional Visitor

Re: Lync Event Log Error 14435 - LS Protocol Stack

Hello Steffen, Looking at your post you say this is now fixed, however I have updated all my VVX400 phones to version 5.9.1.0615 from 5.6.0.17325 and are now seeing the below errors show up on all my FE's. is it possible for someone to have a look into this to make sure the issue is resolved and that this issue is resolved in all future releases ?

 

Error 14435/LS Protocol Stack: At least one invalid authentication signature was detected. There were 1016 messages with invalid signatures in the last 1 minutes. The last one was this SIP message: Trace-Correlation-Id: 3859812376 Instance-Id: 56B402C Direction: no-direction-info Message-Type: request Start-Line: REGISTER sip:FQDN SIP/2.0 From: ;tag=409b77048b;epid=f88c9031ac To: Call-ID: f19ca6e527244d2c969efd5ad4140689 CSeq: 2 REGISTER Contact: ;methods="INVITE, MESSAGE, INFO, OPTIONS, BYE, CANCEL, NOTIFY, ACK, REFER, BENOTIFY";+sip.instance="" Via: SIP/2.0/TLS x.y.z.107:54371;ms-received-port=54371;ms-received-cid=9366100 Max-Forwards: 70 Content-Length: 0 Cause: This could be due to a client or server which is not handling authentication correctly, or it could be due to an attacker. Resolution: None needed unless the failure count is high (>100). Check your network for any rogue clients. Restart the server if problem persists. 

Please note that we didn't have these errors before we updated the Firmware Version. Regards Rony

Message 13 of 14
Polycom Employee & Community Manager

Re: Lync Event Log Error 14435 - LS Protocol Stack

Hello @RonyVI  ,

 

welcome to the Polycom Community.

 

I am not aware of any issue and have not had this seen reported. Please get this into support.

In order to raise a support ticket you need to work with your Polycom reseller as they need to do this for you.

End Customers are unable to open a ticket directly with Polycom support.

If this is some sort of an Internet discounter providing your MAC address or your Polycom devices serial will enable us to look up who would be able to support you. This may not be who you purchased the Polycom device from.

If the unit is no longer within warranty please be prepared to Pay Per Incident / PPI. This is all outlined in detail here

Please ensure to provide some feedback if this reply has helped you so other users can profit from your experience.

Best Regards

Steffen Baier

Polycom Global Services




<======== Signature / Disclaimer ========>
Please be aware:For questions about the type of support to expect please check here

Please also ensure you always check the VoIP , Video Endpoint , Skype for Business , PSTN or RPM FAQ's

Please remember, if you see a post that helped you , and it answers your question, please mark it as an "Accept as Solution".

The title Polycom Employee & Community Manager is an automatic setting within the community and any forum reply or post is based upon my personal experience and does not reflect the opinion or view of my employer.
Poly employee participation within this community is not mandatory and any post or FAQ article provided by myself is done either during my working hours or outside working hours, in my private time, and maybe answered on weekends, bank holidays or personal holidays.
Message 14 of 14