Plantronics + Polycom. Now together as Poly Logo

Provisioning & customization of IP650 phone

Occasional Visitor

Provisioning & customization of IP650 phone

We have a special request about simplification of the call transfer process using the IP 650 phones. Here is what we're trying to accomplish:

 

Today - We use a SwitchVox PBX system that puts a custom image on our IP 650 phones. The image does not allow us to customize the buttons on the phones.

 

The challenge: We have conference bridge functionality in our phone system. When a user is on a conf call its possible that a participant to call the user instead of the conf bridge number. The steps the user must take to get that participant into the conf bridge are as follows:

 

1. Put the conf bridge call on hold

2. Answer the call from the participant

3. Press Transfer

4. Enter extension of conference bridge

5. Press Transfer

6. Go back to the conf bridge appearance.

 

We'd like to simplify this process. In order to do that we need to overwrite the SwitchVox firmware with (i assume) Polycom's default firmware. Then we'd like to customize a hard button on an IP650 to perform #1 and #2 - or #1, #2, AND #3 (so one button for two/three functions -assuming this could be done with a macro). So we're trying to simplify this one process, which apparently is a big enough problem to warrant going this way.

 

I'm looking to find out if:

 

1. Can this be done in the IP650 phones?

2. If so, how do we do it? I found a variety of documents (#42250, #35361) that seem to talk about this but don't exactly provide a step-by-step method of how to do modify the phones.

 

Any help or direction would be appreciated.

Message 1 of 3
2 REPLIES 2
Polycom Employee & Community Manager

Re: Provisioning & customization of IP650 phone

Hello Alex,


Welcome to the Polycom Community.

 

I would recommend, if not already installed, to upgrade your Phones 1st to UCS 3.3.1 Rev F

 

http://downloads.polycom.com/voice/voip/uc/UCagreement_split_3_3_1RevF.html

 

http://downloads.polycom.com/voice/voip/sp_ss_bootrom/spip_ssip_BootROM_4_3_0_release_sig.zip

 

Above is both the UCS 3.3.1 Software and the BootROM 4.3.0

 

Download and unzip above into one directory

 

Polycom Phones require a provisioning Boot Server. This can be HTTP(S),FTP(S) or TFTP

 

Please check the changing the language example at

 

Then read => here <= Above explains how to setup a free FTP Provisioning Server.


Once the Phone is setup to boot from the server check the Technical Bulletins => here <= 

 

Above holds plenty of examples. In addition familiarise yourself with the UCS Admin Guide => here <= 

 

One way to approach your issue would be to utilize so called Enhance Feature Keys. These macros can dial numbers, pause, send dtmf or mimic other complex key stroke sequences.


The CONFIG_FILES="" Section of a 000000000000.cfg is being used to either load templates or own files that you create via an XML Editor or Freeware Editor like notepad++


Open the 000000000000.cfg and store it with the MAC Address of your Phone.


Please be aware that since UCS 3.3.0 we no longer require a sip.cfg or phone1.cfg!


Create a new File for example called buttons.cfg


Below is an example based on a previous SIP Version and should only be used as an example as some commands/parameters have changed in UCS 3.3.x


<feature feature.18.name="enhanced-feature-keys" feature.18.enabled="1"/><softkey softkey.feature.forward="0"/><softkey softkey.2.enable="1" softkey.2.label="SpFwd" softkey.2.action="$FDivert$$FSelect$$FSoftKey2$" softkey.2.use.idle="1"/><divert divert.1.contact="01234"/>


Above was used to remove the original Soft Button for a Call Forward and replace it with a Feature Key/Macro.

 

Now change within the <mac>.cfg CONFIG_FILES="" into CONFIG_FILES="buttons.cfg"

 

Once the Phone reboots you should see the change on your Phone.


Please ensure that you allow to write and append on the FTP Server as the <mac>-app.log and <mac>-boot.log hold valuable Information that will help you troubleshooting any issues.


Best regards


Steffen Baier




<======== Signature / Disclaimer ========>
Please be aware:For questions about the type of support to expect please check here

Please also ensure you always check the VoIP , Video Endpoint , Skype for Business , PSTN or RPM FAQ's

Please remember, if you see a post that helped you , and it answers your question, please mark it as an "Accept as Solution".

The title Polycom Employee & Community Manager is an automatic setting within the community and any forum reply or post is based upon my personal experience and does not reflect the opinion or view of my employer.
Poly employee participation within this community is not mandatory and any post or FAQ article provided by myself is done either during my working hours or outside working hours, in my private time, and maybe answered on weekends, bank holidays or personal holidays.
Message 2 of 3
Highlighted
Valued Contributor

Re: Provisioning & customization of IP650 phone

Hi Alexcrc,

I wanted to clarify this:


@alexcrc wrote:

When a user is on a conf call its possible that a participant to call the user instead of the conf bridge number.


If I'm reading this correctly, users are calling each-other instead of the conference bridge number, so they have to be transferred back to the conference bridge?

 

Wouldnt it be easier to re-direct users to dial the correct conference bridge number instead? :)

 

-James

Message 3 of 3