Plantronics + Polycom. Now together as Poly Logo

Ringer Volume parameter through .cfg file

Occasional Contributor

Ringer Volume parameter through .cfg file

Hi,

 

I am unable to locate the correct parameter for the phone to remember the ringer volume or to specify a specific ringer volume for the phones.

 

I use   voice.volume.persist.handset="1" to set the phone to remember the handset volume although am unable to locate the same parameter for the ringer volume.

Message 1 of 5
4 REPLIES 4
Polycom Employee & Community Manager

Re: Ringer Volume parameter through .cfg file

Hello icsnettech,

 

this feature is currently not supported in UCS 3.3.x and previous SIP Versions.

 

The upcoming UCS 4.0.0 will introduce this feature according to the UCS 4.0.0 Admin Guide:

 

• Persistent Ring—Changes made to the ringer volume by the user persistafter the phone reboots.

 

Best regards

 

Steffen Baier




<======== Signature / Disclaimer ========>
Please be aware:For questions about the type of support to expect please check here

Please also ensure you always check the VoIP , Video Endpoint , Skype for Business , PSTN or RPM FAQ's

Please remember, if you see a post that helped you , and it answers your question, please mark it as an "Accept as Solution".

The title Polycom Employee & Community Manager is an automatic setting within the community and any forum reply or post is based upon my personal experience and does not reflect the opinion or view of my employer.
Poly employee participation within this community is not mandatory and any post or FAQ article provided by myself is done either during my working hours or outside working hours, in my private time, and maybe answered on weekends, bank holidays or personal holidays.
Message 2 of 5
Occasional Contributor

Re: Ringer Volume parameter through .cfg file

Hi,

 

What volume does the phone default to after a call for the ringer?

 

Or does it get adjusted only on phone reboot?

Message 3 of 5
Polycom Employee & Community Manager

Re: Ringer Volume parameter through .cfg file

Hello icsnettech,

 

as long as the Phone is not rebooted the Volume stays at the Level the User can manually adjust.

 

It will reset to the factory default once rebooted.

 

Please read the Using Custom Ring Tones on SoundPoint IP, SoundStation IP, and Polycom VVX 1500 Phones that can be found at the Polycom Technical Bulletin Site => here <=

 

Above explains how a "loud" ring tone can be added that may suit your environment and you could use your own louder Ring Tone until the UCS 4.0.0 is released for your Phones.

 

Best Regards

 

Steffen Baier 




<======== Signature / Disclaimer ========>
Please be aware:For questions about the type of support to expect please check here

Please also ensure you always check the VoIP , Video Endpoint , Skype for Business , PSTN or RPM FAQ's

Please remember, if you see a post that helped you , and it answers your question, please mark it as an "Accept as Solution".

The title Polycom Employee & Community Manager is an automatic setting within the community and any forum reply or post is based upon my personal experience and does not reflect the opinion or view of my employer.
Poly employee participation within this community is not mandatory and any post or FAQ article provided by myself is done either during my working hours or outside working hours, in my private time, and maybe answered on weekends, bank holidays or personal holidays.
Message 4 of 5
Advisor

Re: Ringer Volume parameter through .cfg file

What is the .cfg setting to get a ringer setting to persist after reboot when running 4.0.3.7314?

 

I have tried the following with no positive results. Range I am using is -21 to 0

 

<voice voice.gain.rx.analog.ringer.IP_650="0">

<voice voice.gain.rx.digital.ringer.IP_650="0">

<voice voice.gain.rx.analog.ringer="0">

<voice voice.gain.rx.digital.ringer="0">

Message 5 of 5