configuring polycom speeddials (attendants ) makes phone reboot

[milansuthar]

attendant.resourceList.1.address="54564654"
attendant.resourceList.1.label="milan suthar"
attendant.resourceList.1.type="normal"

configuring above settings for speeddial makes phone reboot only when it changes not when same configuration apply with diffrent value,

i.e when apply new attendants , or removing all attendants.
 i want to make phone reboot stop

[SteffenBaierUK]

Hello @milansuthar ,

Welcome back to the Poly Community.

Some or a couple of your old post(s) or reply(s) to them => here <= are still open/pending as you have not marked these as "Accept as a solution" or at least provide some form of feedback or answer.

If they are in this state nobody finding them via a community search will know if an answer or advice provided was useful and has maybe helped you.

Could you therefore kindly go over them and mark or answer as appropriate?

If they are marked as "Accept as a solution" other users can find these easier and it helps them to utilise the community more efficiently. Please do not simply mark them without any type of feedback.

As a reminder for any new post:

Both the communities Must Read First and the FAQ reference the basic minimum information a new or follow up post should contain.

This ensures the questions having to be asked are limited and any new or follow up post contains the right amount of details to ensure any voluntary participant within the community does not spend additional time chasing basic information.

As a reminder the basic information asked for:

• Provide the exact Software Version of your Phone
• Provide the Phone Model
• Provide the Call Platform (aka openSIP,Teams, Skype for Business Online, Skype for Business on Premise, Lync)
• Provide details if UC / SIP or ObiEdition
• Additional Poly Infrastructure (RPRM,PDMS or BToE)
• If applicable provide a backup of the phone in question

UC Software 4.0.0 or later via the Web Interface Utilities > Phone Backup & Restore > Phone Backup > Phone Backup. Please rename into .TXT or Zip the file to attach.
Since UC Software 5.9.0 simply provide this via the Web Interface Diagnostics > Download Support Information Package

• If possible provide a Log and either attach them or use the Code Tag.Consult the Troubleshooting Section found within the FAQ if applicable
• If possible provide the MAC Address or Serial of the device
• Provide details for example if the issue is a day 1 issue or only happened after an upgrade or any other relevant details
• For questions around Support please check here

Whilst providing some of these details may not directly impact any possible answer the community can provide, it does enable Poly to have an overview of the current software used. In addition, providing all details at the same time allow us to check logs or look up potential support partners if an issue needs to come into support. It also enables us to verify the entitlement for using features.

Without the above, we are unable to make any meaningful suggestions as we do not know any details about your setup.

Please ensure to provide some feedback if this reply has helped you so other users can profit from your experience.

Best Regards

Steffen Baier

[milansuthar]

Phone Information
Phone Model	VVX 410
Part Number	3111-46162-001 Rev:A
MAC Address	64:16:7F:94:F8:B7
IP Mode	IPv4
IP Address	172.16.16.239
UC Software Version	5.5.2.8571
Updater Version	5.7.2.21547

this is phone information i am using.

[SteffenBaierUK]

Hello @milansuthar ,

I have seen you marked >here< and >here< as solution provided.

What was the actual solution for >here<?

Without this, the marked post has no meaning and does not help anybody.

For >here< the suggestions where to get this into support and/or work with Broadsoft.

Again which was your solution for the issue?

Prior to explaining and documenting this, we will not be able to answer or try and help you with your new issue.

Best Regards

Steffen Baier